1 1

SikaShield W159

SikaShield W159

₱10,700.00
₱10,700.00
结账时计算的运费。

SikaShield® W159 ED 1,5 mm | Wet Applied Bituminous Waterproofing

 

An adhesive bituminous waterproofing membrane wet applied to the concrete surface by the adhesive mortar SikaShield® W1. It has a thickness of 1.5 mm and is flexible at -15 °C. It is reinforced with a cross-laminated PE film, which gives high mechanical properties to the membrane. The top surface and the underside have a removable liner over the adhesive compound for an easy application.

 

Packaging: 1m x 20m / roll

Note: use for adhesive use Sikabit W1

 

Uses / Area of Application

The Product is used as a waterproofing membrane for:

- Basements and other below ground structures

- Vertical reinforced concrete walls 

- Single and strip foundations

 

The Product is used as a:

- Single layer under heavy protection 

- Base sheet in multi-layer systems

Please note: The Product is not suitable for roofs permanently exposed to UV radiation.

其他人一起购买了此产品
Sikabit W-1

₱1,240.00

查看完整详细信息

指示

APPLICATION

1. Unroll the membrane. Align the membrane. Re-roll the membrane before application.

WET APPLICATION
1. Preconditions Before the application of the adhesive mortar, the concrete substrate has been saturated with water. The adhesive mortar SikaBit® W1 has been applied onto the substrate and is still wet.

2. Lay the membrane directly over the wet adhesive mortar. At one end of the membrane, peel away part of the release liner from the membrane's underside.

3. Bond this end of the membrane to the adhesive and the substrate.

4. Continue to peel away the release liner sideways from the rest of the membrane's underside.

5. Bond the rest of the membrane to the adhesive and the substrate.

IMPORTANT
1. If the ambient temperature is below +10 °C, seal the membrane overlaps by heating them with a gas torch or with hot air.

2. Seal the membrane overlaps to avoid trapping the adhesive under the overlap, which can compromise the adhesion.

3. Roll the surface of the applied membrane with a roller from the centre to the edge to remove any air bubbles.

4. Push any excess of adhesive towards the opposite direction of the sealed side overlap. Allow the adhesive mortar to cure for at least 24 hours at +25 °C before you start backfilling.

DETAILING
1. Use a sharp knife to cut in all details such as internal and external corners, upstands, vent pipes, drains, support metalwork etc.

Refer to the relevant method statement for further information on detailing.

付款和运输

付款方式：
(1) Paymongo：万事达卡、VISA、GCash、Maya、Grab Pay
（2）网上银行转账至我们的 BDO、Metrobank 和 BPI 账户有关更多详情，请查看接受的付款方式

运输：
（客户地点）位于马尼拉大都会 (NCR)

（1）加急——当天取货
（2）定期取货
（3）通过第三方提货/送货*
（4）送货至马尼拉大都会的站点**
Lalamove/抓钉：LPM 建筑供应和木材中心公司


（客户所在地）位于 Pangasinan

（1）加急——当天取货
（2）定期取货
（3）通过第三方提货/送货*
（4）运送至邦阿西楠省的现场位置**
Lalamove/抓斗销：LPM Construction Supply PangasinanBrgy, Tayug-San Quintin Rd.塔于格,
菲律宾邦阿西楠省